#ARDUINO DOWNLOAD HOW TO#
#ARDUINO DOWNLOAD SERIAL#
#ARDUINO DOWNLOAD DRIVERS#
#ARDUINO DOWNLOAD SOFTWARE#
#ARDUINO DOWNLOAD CODE#

It communicates using the original STK500 protocol. You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header using Arduino ISP or similar.

#ARDUINO DOWNLOAD CODE#

Select 'Arduino Duemilanove or Nano w/ ATmega328' from the Tools > Board menu (according to the microcontroller on your board). The ATmega328 on the Arduino Nano comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer.

#ARDUINO DOWNLOAD SOFTWARE#

The Arduino Nano can be programmed with the Arduino software ( download). To use the SPI communication, please see ATmega328 datasheet. The Arduino software includes a Wire library to simplify use of the I2C bus. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1). A SoftwareSerial library allows for serial communication on any of the Nano's digital pins. The ATmega328 also support I2C (TWI) and SPI communication. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board.

#ARDUINO DOWNLOAD DRIVERS#

An FTDI FT232RL on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The ATmega328 provide UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). The Arduino Nano has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. Typically used to add a reset button to shields which block the one on the board. Bring this line LOW to reset the microcontroller. There are a couple of other pins on the board: Support I2C (TWI) communication using the Wire library (documentation on the Wiring website). Additionally, some pins have specialized functionality: Analog pins 6 and 7 cannot be used as digital pins.

By default they measure from ground to 5 volts, though is it possible to change the upper end of their range using the analogReference() function. The Nano has 8 analog inputs, each of which provide 10 bits of resolution (i.e. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off. There is a built-in LED connected to digital pin 13. These pins support SPI communication, which, although provided by the underlying hardware, is not currently included in the Arduino language. Provide 8-bit PWM output with the analogWrite() function.

See the attachInterrupt() function for details. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. These pins are connected to the corresponding pins of the FTDI USB-to-TTL Serial chip. Used to receive (RX) and transmit (TX) TTL serial data. In addition, some pins have specialized functions: Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. Input and OutputĮach of the 14 digital pins on the Nano can be used as an input or output, using pinMode(), digitalWrite(), and digitalRead() functions. The ATmega328 has 2 KB of SRAM and 1 KB of EEPROM. The ATmega328 has 32 KB, (also with 2 KB used for the bootloader. The power source is automatically selected to the highest voltage source. The Arduino Nano can be powered via the Mini-B USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). You can find here your board warranty information. Need any help with your board please get in touch with the official Arduino User Support as explained in our Contact Us page.

#ARDUINO DOWNLOAD HOW TO#

Need Help?Ĭheck the Arduino Forum for questions about the Arduino Language, or how to make your own Projects with Arduino. You can find in the Getting Started with Arduino Nano section all the information you need to configure your board, use the Arduino Software (IDE), and start tinkering with coding and electronics.įrom the Tutorials section you can find examples from libraries and built-in sketches as well other useful information to expand your knowledge of the Arduino hardware and software. If you are looking for a Nano board with similar functionality but also provide additional features, check:įind inspiration for your projects with the Nano board from our tutorial platform Project Hub. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one. It has more or less the same functionality of the Arduino Duemilanove, but in a different package. The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano 3.x).

Arduino download